Product Description
Complete wheel kit GWK-HPT25-CK for Toyota HPT25 manual pallet jacks. Includes ultra-polyurethane 2.90 inch diameter load wheels (Shore D 70 hardness), poly steer wheels with ball bearings, axles, and fasteners. Designed for OEM-equivalent fit and function with exact tolerances.
Compatibility: Fits pallet jacks made by Toyota, model HPT25. SKU: GWK-HPT25-CK
Specifications
Material & Construction
| Load Wheel Hardness | Shore D 70 |
| Steer Wheel Construction | Polyurethane tire bonded to steel wheel core |
Part Numbers
| Manufacturer Part Number | GWK-HPT25-CK |
| OEM Compatibility | Toyota HPT25 Manual Pallet Jack |
Frequently Asked Questions
Q: Is GWK-HPT25-CK compatible with other Toyota pallet jack models?
A: GWK-HPT25-CK is engineered specifically for the Toyota HPT25 model. Do not use this kit on HPT20, HPT30, or other Toyota models. Wheel diameter (2.90 inch), axle mounting patterns, and steer wheel dimensions are unique to the HPT25 frame geometry. Using an incompatible wheel kit will result in poor handling, accelerated bearing wear, and potential safety hazards. Always verify your pallet jack model plate before ordering.
Q: What is included in the GWK-HPT25-CK kit and what is pre-assembled?
A: GWK-HPT25-CK includes two ultra-poly (Shore D 70) load wheels with ball bearings, two poly steer wheels with sealed ball bearings, steel axles, and mounting fasteners. The load wheels and steer wheels arrive with bearings already installed on the axles. The kit is 95 percent pre-assembled; you install the wheel-axle subassemblies into your HPT25 frame using the fasteners provided. No separate bearing installation is required. Typical installation time is 30-45 minutes.
Q: How do I know if GWK-HPT25-CK is the right replacement for my HPT25 jack?
A: Confirm your jack is a Toyota HPT25 by checking the frame nameplate or serial number plate (usually on the handle or lower frame). The HPT25 typically has a 2500-3000 lb capacity rating. If your jack is labeled HPT20, HPT30, or another model, GWK-HPT25-CK is not compatible. If you are unsure, measure the existing wheel diameter (should be approximately 2.90 inches) and compare to the kit specifications.
Q: What is the load rating and duty limitation for GWK-HPT25-CK?
A: GWK-HPT25-CK wheels are rated for the full duty capacity of the HPT25 frame, typically 2500-3000 lb at 24 inch load center. The ultra-poly (Shore D 70) construction is rated for standard warehouse duty: smooth concrete, typical 8-10 hour shifts, and loads distributed evenly on the forks. Do not exceed the pallet jack frame capacity. Operation on uneven, rough, or outdoor surfaces will reduce wheel lifespan by 30-50 percent.
Q: Can GWK-HPT25-CK steer wheels be replaced separately from load wheels?
A: You may order steer wheel subassemblies separately through OEM part sourcing if only front wheels are damaged. However, GWK-HPT25-CK is sold as a complete kit for cost efficiency and to ensure all wheels age uniformly. If only steer wheels are worn, you can request a partial kit from the OEM supplier, but sourcing may take longer than ordering the complete kit. Always replace load and steer wheels as matched pairs within the same maintenance cycle for balanced handling.
Q: What maintenance extends the lifespan of GWK-HPT25-CK wheels?
A: Perform weekly visual inspections for cracks, flat spots, or bearing noise. Keep wheels and axles clean of debris and dried hydraulic fluid. Every 6 months, spin each wheel by hand to verify smooth, quiet rotation; if you hear grinding or squealing, the bearing is degrading and wheels should be replaced. Do not hose down sealed bearings with high-pressure washers. Typical warranty is 12 months from date of installation; wheels last 3-5 years under normal conditions. Replace as a complete kit when any wheel fails.